Siloxane Clear Deodorised

Clear waterproof coating for concrete, brick, natural stone & other masonry surfaces.

DESCRIPTION:

SILOXANE CLEAR is an oligomeric siloxane, when applied to concrete, brick and natural stone facades, provides a waterproof finish without changing the outward appearance. Impregnation with SILOXANE CLEAR reduces the ingress of water, preventing water-related problems: e.g. reinforcement corrosion, binder loss and biological promoted decay due to moss.
SILOXANE CLEAR, unlike Silicone, is suitable for use in high pH conditions e.g. new concrete, lime mortars and lime based building bricks/blocks.

The product does not affect the vapour diffusion, allowing the façade to breathe. Historical examination of completed projects suggests that when applied correctly, a SILOXANE CLEAR treated façade is still water repellent after 10 years service.
APPLICATIONS:
External waterproofing of block and brick, fibrous sheet and porous tile facades.· Prevention of moss growth and dirt retention on pavers, walls and roofs.· Reduction of sandstone decay due to salts and low pH precipitation.
Elimination of white salt spotting. Treatment of rising damp in old homes. Protection of reinforced concrete against steel corrosion by chloride diffusion.

Siloxane Clear is available in 20 and 10 litre drums.
SPECIFICATIONS:

Product Oligomeric iso-octyl silane, in a mineral spirit base,13 % active.

Coverage Varies widely, dependant on absorption characteristics. E.g. from 3 m2/lit for concrete to ½ m2/lit. for highly porous material. A trial area of 1-2 m2 will assist in determining application rate.

A wall treated with Siloxane Clear will not allow moisture to penetrate, reducing evidence of salts and the growth of moss and mildew.

Example of two bricks, one coated with Siloxane Clear (top) water is seen to be beading on the surface. The other brick not coated is absorbing water.

Application

Using a low-pressure spray (hand pump pressure pot) or brush to achieve total saturation with a minimum of 2 coats applied sequentially (wet on wet) 3mm penetration minimum.

SURFACE PREPARATION
Hairline cracks need not be filled however cracks wider than 0.3mm should be sealed. Repair damaged expansion joints, and faulty junctions Clean dirty surfaces and remove algae or moss before impregnation (treat with suitable fungicide). Cleaned surfaces are easy to impregnate because absorbency is increased resulting in maximum penetration of treatment. Allow surfaces to dry before applying
SILOXANE CLEAR treatment. Any salt and effervescence should be removed using diluted acid.

APPLICATION PROCEDURES

To ensure that sufficient impregnate enters the surface, SILOXANE CLEAR should be applied by spraying or flooding.
Larger areas are best treated using low-pressure airless spraying.
Smaller areas can be treated by brush applying SILOXANE CLEAR– adhering to the application rate.
When spraying, the distance between the nozzle and the wall should be 5-10cm. SILOXANE CLEAR is applied until no more is absorbed and the solution runs down 40-50cm. The spraying nozzle is then slowly moved on, horizontally. With this method care should be taken that the substrate is evenly wet during application.

Siloxane Clear can also be used to seal porous natural stone without leaving an unnatural glossy finish.
Protection During Use
Protect overspray and splashes from windows, doors, vehicles and vegetation Since dry, impregnated surfaces look the same as unimpregnated ones, it is advisable to thoroughly treat a specified area of the surface twice, without interruption.

QUICK-SET HYDRAULIC MORTAR STOPS LEAKS UNDER PRESSURE

Description

View Maxplug Video | Technical Brochure | MSDS | Specifications

Uses

MAXPLUG is a quick-setting hydraulic cement that instantly stops running water from cracks, holes or other openings in concrete and masonry, once it sets. It does not contract and sets within three to five minutes depending on the temperature. It only requires water for mixing.

• To seal leaks instantly in concrete surfaces and solid masonry.
• For emergency repairs on water pipes. For broken pipes, sometimes MAXPLUG will even work when the pipes are under pressure.
• Emergency plugging of gas leaks.
• To anchor bolts and other accessories that require immediate use.
• In basements, tunnels and sewers, to stop water under pressure.

Advantages

• The coating allows the base to transpire and thereby eliminates water vapour.
• Stops leaks and waterproofs the surface to which it is applied.
• Does not contract, or become weak due to its exothermic reactions.
• It increases in volume. Its rapid set, three to five minutes, may be controlled (either speed up or slowed down) by adding warm or cold water. The setting may even be instantaneous.
• It is the proper maintenance material for homes and industry.
• It is not toxic when it comes into contact with drinking water.
• Its mechanical properties are comparable to those of concrete, and in some cases even superior.
• It sets under water.

Applications

• To seal leaks instantly in concrete surfaces and solid masonry.

• For emergency repairs on water pipes. For broken pipes,

MAXPLUG

will even work when the pipes are under pressure.

• Emergency plugging of gas leaks

• To anchor bolts and other accessories that require immediate use.

• In basements, tunnels and sewers, to stop water under pressure.

Tools

MAXPLUG can be applied with a trowel, a spatula or even by hand. As any abrasive material, make sure to use protective rubber gloves when applying by hand.

How to mix

Mix only the amounts of MAXPLUG that can be applied in three minutes; if it is a water leak, mix only the amount of material that can be used with your hand. Use a plastic or rubber container, fill with MAXPLUG as needed, and add water slowly until it has the consistency of cement mortar.

One kilogram of MAXPLUG requires 280 cc of water.

How to Use

Normal weather, MAXPLUG takes between three to five minutes to set, depending on the temperature of the product, the water and atmospheric condition. Three to five minutes setting time is for temperatures in the 18º to 20º C range.

Warm weather, when temperatures are high and MAXPLUG sets very quickly, cold water must be used to delay the setting time, allowing you time to apply the material.

In extreme cases, keep the product in the shade and add ice to the mixing water.

Cold Weather, at a low temperatures, use warm or hot water to prepare maxplug mixes. At extremely low temperatures, i.e., below 0º C, heat the material and use hot water.

Surface Preparation. All cracks should have a minimum depth of 2 centimetres and an opening of 1.5 to 2 centimetres. Make a square-shaped cut, preferably dovetail to the surface to which the material is to be applied; avoid the “V” shape. See drawing above. Clean the surface until it is free of all loose materials; wet the surface if water is not present at the time of application. Use MAXPLUG without force.

Sealing Concrete Walls and Slabs

Once the surface has been prepared by removing the loose concrete from the crack and cutting to a depth of 5 cms., apply maxplug in small amounts. Mix only the amount of material that can be applied by hand; do not pour the material in place; always use your hands. Wait until it becomes warm before applying, immediately remove the excess material and continue until the crack is finished. Under great pressure, in tunnels and basements do not try to plug up the crack at once.

Maxplug is ideal to anchor bolts and metal fixtures to concrete.

Sealing concrete slabs and walls

This is very common in basements, elevator shafts, swimming pools and water towers. Make sure there is an opening of at least 2 x 3 cm., and seal it with MAXPLUG making a waterproof cove at the joint of floor and wall.

Sealing Process View Maxplug Video

Leaks in cracks or joints

Once the surface has been prepared by removing the loose concrete from the crack and cutting to a depth of 5 cms., apply MAXPLUG is small amounts. Mix only the amount of material that can be applied by hand; do not pour the material in place; always use your hands. Wait until it becomes warm before applying, immediately remove the excess material and continue until the crack is finished. Under great pressure, in tunnels and basements do not try to plug up the crack at once.

Expansion joints.

MAXPLUG, a rigid product once it has set is not the ideal material for this type of work since expansion joints are subject to constant movement. Nevertheless, it is used to stop the water in expansion joints; later, when it is dry, the expansion joint is made with a flexible material.

MAXPLUG is ideal to anchor bolts and metal fixtures to concrete.

Technical data

Mechanical resistance

Test No 14-1/83-M INCE, Madrid.

Product requirements.

One kilogram of MAXPLUG fills approximately 0.6 cubic decimeters.

Packaging

25 kilogram drums and 5 kilogram cans, and 1kg handy pack.

Caution

As all cement products, MAXPLUG is abrasive a protective rubber gloves must be used to prepare the mixture and apply it. If any of the mixture gets into the eyes, rinse thoroughly with clean water, but do not rub. If irritation continues, consult a doctor.

Expansion Joints

Maxplug, a rigid product once it has set is not the ideal material for this type of work since expansion joints are subject to constant movement. Nevertheless, it is used to stop the water in expansion joints; later, when it is dry, the expansion joint is made with a flexible material.

Maxplug is ideal to anchor bolts and metal fixtures to concrete.

GuaranteeThe information contained in this leaflet is based on our experience and technical knowledge, obtained through laboratory testing and from bibliographic material. DRIZORO reserves the right to introduce changes without prior price. Any use of this data beyond the purposes expressly specified in the leaflet will not be the Company´s responsibility unless authorised by us. The data shown on consumptions, measurement and yields are for guidance only and based on our experience. These data are subject to variation due to the specific atmospheric and jobsite conditions so reasonable variations from the data may be experienced. In order to know the real data, a test on the jobsite must be done, and it will be carried out under the client responsibility. We shall not accept responsibility exceeding the value of the purchased product. For any other doubt, consult our Technical Department. This version of bulletin replaces the previous one.

Hydraulically Expanding Mortars

MAXGRIP – ANCHORING CEMENT FOR CONCRETE AND MASONRY

Description

Maxgrip is a mixture of cements and selected special additives and aggregates. A pourable, cement-base, non-shrinking, quick-setting hydraulic compound.

Technical Data |MSDS| Specifications

Uses
Water/Sewer Management, Road/Rail, Construction Building/Swimming Pool Industry, Bridge Building, Councils, Heavy Industry, Mining, Steel, Defence Forces.

• Setting anchor bolts, rail posts, signposts. Parking meters, reinforcing rods and fixtures.
• Heavy machinery anchoring, hooks, pulleys.
• Park seats, bridge railings, partitions.
• Safety rails, hand rails, balustrades.
• Flag and light poles.

Advantages

• Quick setting – 15 minutes.
• Stronger than concrete in one hour.
• Grey Colour matching perfectly with concrete. Makes structurally sound bonds.
• Add water only – easy use.
• Waterproofs surface to which it is applied.
• Non-toxic. Odourless.
• Ideal for badly ventilated areas. Pourable.
• Contains no sulphur or Iron particles, will not oxidise.

Hydraulically Expanding Mortars

A Flexible Waterproof Coating Against Positive And Negative Pressure For Concrete, Masonry, Blocks, Pre-Fabricated Panels And Brick

Description
Video | Technical Brochure | MSDS Part A | MSDS Part B | Specifications
Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. Waterproofing of below-grade structures like basements, retaining walls, foundations, tunnels, galleries subjected to both positive or negative high water pressure. Internal and external waterproofing and protection of new and old buildings, façades against dampness, rain, pollution and aggressive environments. Waterproofing and protection of concrete against carbonation, freeze-thaw cycles, de-icing salts in highways and chlorine penetration in public works, irrigation channels, dams, retaining walls and water treatment plants, bridges, etc.
Tile fixing and waterproofing of bathrooms, kitchens and other wet rooms in hotels, hospitals, offices and residential buildings, also suitable for exterior applications.

MAXSEAL FLEX is a coating with flexible and waterproofing properties that adheres to practically every surface such as concrete, natural and artificial stone, mortar plasters, bricks, concrete blocks, etc. subjected to both positive or negative high water pressure

Waterproof coating that adheres to common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks.

Once applied and cured, MAXSEAL FLEX provides a non-toxic, flexible and waterproof coating that adheres to those common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks.

Description

MAXSEAL FLEX is a two component product: Component A is a mortar based on a mixture of special cements, additives and well-graded fillers and Component B is a liquid based on special synthetic resin. MAXSEAL FLEX is a coating with flexible and waterproofing properties that adheres to practically every surface such as concrete, natural and artificial stone, mortar plasters, bricks, concrete blocks, etc.

Once applied and cured, MAXSEAL FLEX provides a non-toxic, flexible and waterproof coating that adheres to those common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks.

Application Fields

• Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools.
• Waterproofing of below-grade structures like basements, retaining walls, foundations, tunnels, galleries subjected to both positive or negative high water pressure.
• Internal and external waterproofing and protection of new and old buildings, façades against dampness, rain, pollution and aggressive environments.
• Waterproofing and protection of concrete against carbonation, freeze-thaw cycles, de-icing salts in highways and chlorine penetration in public works, irrigation channels, dams, retaining walls and water treatment plants, bridges, etc.
• Tile fixing and waterproofing of bathrooms, kitchens and other wet rooms in hotels, hospitals, offices and residential buildings, also suitable for exterior applications.
• Waterproofing of jardinieres, terraces and balconies under the pavement.

Advantages

• Provides a fully-flexible coating which ensures complete waterproofing even in the most severe conditions, as high negative water pressure.
• Covers shrinkage and hairline cracks of the concrete.
• Acts as an anti-fracture membrane between the substrate and other finishing coats if applied.
• Excellent protection for concrete, being both a CO2 an chlorine (Cl-) barrier and thereby preventing carbonation and electrochemical corrosion.
• Permeable to water vapour, allows the substrate to breathe.
• Resistant to abrasion and UV rays.
• Withstands atmospheric pollution, corrosive effects of salt water and de-icing salts and freeze/thaw cycles.
• Resists hydrostatic negative pressure from ground water when used for underground interior applications.
• Excellent adhesion and easy to use. Does not require bonding agents and can be applied on wet surfaces
• Non-toxic and chloride-free. Suitable for contact with potable water.
• Longer lasting that other coatings, avoiding maintenance costs.
• Environmentally friendly
• Specially recommended to complement other products of DRIZORO system as MAXSEAL

Application Images

Application Instructions

Water Proofing and Protective Cement Based Coatings

MAXREST is a one-component structural repair mortar, made of special cements, additives and selected aggregates, which provides a thixotropic product with quick-setting that does not shrink. It firmly adheres to the surface which it is applied on, and restores concrete to its original condition

Description
View Video | Navy Job Video | Technical Data | MSDS | Specifications

Application Fields

• For general repair and restoration work on structural concrete. Repairs honeycombs, cracks and fissures.
• Patching and protective covering of superficial reinforcing rods affected by corrosion.
• To repair lintels, raincaps, water tanks and to restore architectural concrete permanently exposed to climatic conditions.
• Sealing of construction joints previous to waterproofings works in tanks, swimming pools, basements, etc.
• For restoration of lines and shapes of damaged pre-fabricated concrete elements.

Advantages

• Its quick-setting time, from 15 to 20 minustes, allows for an agile repair process.
• It forms part of the substrate and the repairs are structurally sound, with properties comparable or higher than concrete.
• Very good thixotropy without slump or the need for using form work.
• It does not shrink, avoiding risk of cracks when sets.
• Odour-free and non-toxic, making it the ideal material to use in badly ventilated places, such as water tanks, shafts, sewers, etc.
• Does not contain any chloride.
• Only needs the addition of water for mixing.

Surface preparation and repair.

Finished Application

Concrete Repair Mortars

NORMAL SETTING, POLYMER-MODIFIED, FIBER-REINFORCED, STRUCTURAL REPAIR MORTAR WITH CORROSION INHIBITORS

Description
Technical Data | MSDS| Specifications

MAXRITE 700 is a single component, cement-based, microsilica and polymer-modified, fiber- reinforced restoration mortar with corrosion inhibitors. It is specially designed for high performance structural concrete repair exposed to an aggressive environmental ambient and provides an additional protection of the steel reinforcements. Its long open time and thixotropy allow the repair of new and old concrete in a simple way, without the need for using any form work, applied manually or by mechanical means.
Application fields

• Maintenance of industrial areas damaged by aggressive environment, acid rain, atmospheric pollution, etc.
• Structural concrete repair affected by corrosion of reinforcements in marine environment, bridges, harbours, dams, etc
• Repair of concrete structures with carbonation process.
• Repair of damaged concrete by deicing-salts, freeze/thaw cycles, mechanical impacts, etc.
• Concrete repair affected by repeated loads.
• Repair of pre-fabricated concrete elements.

Advantages

• Corrosion inhibitors prevent corrosion against chlorides and aggressive corroding agents, extending considerably the service life of the structure.>
• Its open setting time allows the quick completation of the repair of large surfaces.
• Good chemical resistance in aggressive environmental ambient due to its microsilica content.
• Waterproof. Withstands freeze/thaw cycles.
• Offers high resistance to carbonation penetration.
• High adhesion to concrete and reinforcements. Does not require special primers. Loads are transmitted onto the repaired structure.
• High impact and mechanical strength. Long lasting repairs.
• Good thixotropy. Application in successive layers without slump or the need to use form work. Allows high thickness per layer.
• Easy workability and application. It can also be sprayed by wet method.
• Single component mortar. Only requires water for mixing and it is odourless, making it suitable for poor ventilated areas.

Application Instructions

Concrete Repair Mortars

View Video | Technical Data | MSDS| Specifications

Water Proofing and Protective Cement Based Coatings

MAXPATCH – TWO COMPONENT MORTAR FOR RESTORATION OF INDUSTRIAL CONCRETE PAVING IN MINIMUM THICKNESS

Description
The product is made up of two components: a cement base with special aggregate and a liquid resin. These are mixed together to form an advanced mortar for repairs to floors, ramps, steps etc… It has strong adhesion, is resistant to abrasions and is non slip.

Uses

• For restoration of industrial roads.
• To patch eroded concrete floors or to raise height.
• For non-slip ramp constructions, it is resistant to traffic wear.
• To repair concrete steps and stairs.

Advantages

• Non slip.
• From 5 mm. to 25 mm., thickness increase can be made.
• Can be used for filling voids or holes in floors.
• Quick setting: within 24-48 hours.
• Can be painted when dry or coloured by the addition of dye during mixing.
• Highly resistant to industrial acids and other pollutants.

Application instructions

Concrete Repair Mortars

Concrete Repair Mortars.
]]> http://hanmawaterproofingproducts.com.au/197/two-component-restoration-mortar/feed/ 0 http://hanmawaterproofingproducts.com.au/194/quick-setting-levelling-mortar/ http://hanmawaterproofingproducts.com.au/194/quick-setting-levelling-mortar/#comments Tue, 15 Nov 2011 03:59:08 +0000 admin http://hanmawaterproofingproducts.com.au/?p=194 Drizoro Quick Setting Levelling Mortar



Watmat QUICK SETTING MORTAR FOR LEVELLING MANHOLE COVERS AND FOR REPAIRS FOR IMMEDIATE USE.

Description

WATMAT is a quick setting mortar, factory mixed with special cements, silica and additives. It is ready for use for levelling newly constructed manholes and urgent repairs to factory floors.

Advantages

• For emergency repairs and resetting manhole covers on streets, public roads and concrete factory floors.
• Traffic can pass over the repair within two hours of application.
• Just mix with water.
• The addition of MAXCRYL to the mixing liquid produces an even stronger mixture.
• It adheres well to the substrate and its grey colour blends in with the concrete.
• It is non-toxic and odourless which makes WATMAT an ideal product for areas with little ventilation.
• Waterproof. Very low water absorption.

Setting

Once mixed to a mortar consistency, WATMAT can take from 5 to 20 minutes to set, according to the climatic and surface temperatures. Trials should be carried out to establish that whatever quantities you mix can be applied before the material starts to set.

Application Instructions

Concrete Repair Mortars

]]> http://hanmawaterproofingproducts.com.au/194/quick-setting-levelling-mortar/feed/ 0 http://hanmawaterproofingproducts.com.au/188/fast-setting-patching-material/ http://hanmawaterproofingproducts.com.au/188/fast-setting-patching-material/#comments Tue, 15 Nov 2011 03:49:33 +0000 admin http://hanmawaterproofingproducts.com.au/?p=188 Drizoro Maxroad Water Proofing and Patching Cement Based Material



CEMENT BASE FAST SETTING PATCHING MATERIAL FOR CONCRETE BRIDGE DECKS, EXPRESSWAYS

Description
Technical data | MSDS| Specifications
A cement-base, fast-setting patching material that develops high compressive strenghts and will allow traffic bearing patches to be put back in service after 2 hours from time of placement.

Uses

• Urgent repairs in concrete pavements subject to permanent traffic.

 

Advantages

• Good adherence.
• Can be applied to damp surfaces.
• Traffic bearing 2 hours approximately.
• Fast-setting.
• Freeze-thaw resistant.
• Contains no chlorides.
• Easy to apply.
• Product of an only component.

 

Application Instructions

 

Concrete Repair Mortars

]]> http://hanmawaterproofingproducts.com.au/188/fast-setting-patching-material/feed/ 0